Israel DLM10 Series (EKE Series) Multi-disc Electromagnetic Clutch

In order to ensure the uninterrupted operation of the electromagnetic clutch, it must be maintained and maintained frequently: during use, the electromagnetic clutch will have different failures due to various factors. The general failure of the electromagnetic clutch mostly occurs during starting, idling and load, but it occurs more often during the starting period, mainly manifested as failure to start, or the voltage input to the electromagnetic clutch is too low, and the regular input voltage is DC24V.

Category:

IsraelMulti-disc electromagnetic clutch

Phone:400-888-8888

Inquire

Product Description

In order to ensure the uninterrupted operation of the electromagnetic clutch, it must be maintained and maintained frequently:
1. Always check the tightening degree of the bolts, especially tighten the bolts of the electromagnet, the bolts of the electromagnet and the housing, the bolts of the yoke, the bolts of the electromagnet coil and the terminal bolts.
2. Lubricant is often added to the movable part of the electromagnetic clutch.
3. Regularly check the mechanical wear of the movable parts, and remove the dust, flower hair and dirt on the surface of the electromagnet parts.
4. Regularly check the length of the armature stroke. This is because, during operation of the clutch, the stroke length of the armature will increase due to wear of the cutting surface. When the armature stroke length does not reach the normal value, it must be adjusted to restore the minimum gap between the braking surface and the turntable. If the armature stroke length is increased above the normal value, the suction force may be greatly reduced.
5. If the worn braking surface is replaced, the minimum clearance between the braking surface and the turntable should be properly adjusted.
During use, the electromagnetic clutch will have different failures due to various factors. The general failure of the electromagnetic clutch mostly occurs during starting, idling and load, but it occurs more often during the starting period, mainly manifested as failure to start, or the voltage input to the electromagnetic clutch is too low, and the regular input voltage is DC24V. As well as unstable power, slippage or high temperature, but there are also special circumstances.
Therefore, pay attention to the requirements when inputting the voltage. The elimination method is to detect whether the input voltage is the required voltage of the electromagnetic clutch. The coil is short-circuited, and this kind of fault is usually replaced or repaired. It is recommended to replace or modify the electromagnetic clutch circuit.

Main performance parameters
Main Technical Data

Specifications Model	Rated dynamic torque Rated Torque (N.M)	Rated static moment Rated Static Torque N.m	no-load moment Drag Torque (≦) N.m	On time Engagement Time (≦)S	Disconnection time Disengagement Time (≦)S	Rated voltage Rated Voltage D.C(V)	Coil power consumption (20 ℃) Coilpower(20℃)W	Maximum allowable speed Max Allowed Speed（r/min）	Weight weighnt（kg）
1A/1A.G	12.5	20/14	0.088/0.05	0.14/0.11	0.03/0.025	24	26	3000	2
2A/2A.G	25	40/27.5	0.175/0.10	0.18/0.14	0.032/0.028	24	27	3000	2.6
4A/4A.G	40	63/44	0.280/0.16	0.20/0.18	0.04/0.03	24	33	3000	3.2
6A/6A.G	63	100/70	0.350/0.26	0.25/0.20	0.045/0.04	24	43	3000	4
10A/10A.G	100	160/110	0.500/0.35	0.28/0.25	0.06/0.045	24	43	3000	5.5
16A/16A.G	160	250/175	1.00/0.56	0.30/0.28	0.08/0.06	24	47	2500	7.8
25A/25A.G	250	400/280	1.50/0.88	0.35/0.30	0.11/0.08	24	55	2200	11
40A/40A.G	400	630/440	2.50/1.40	0.40/0.35	0.12/0.11	24	62	2000	15
63A/63A.G	630	1000/700	4.00/2.20	0.50/0.40	0.15/0.12	24	70	1750	21
100A/100A.G	1000	1600/1100	6.00/3.00	0.60/0.50	0.18/0.15	24	79	1600	32
160A/160A.G	1600	2500/1750	10/5.5	0.90/0.70	0.22/0.18	24	93	1350	50
250A/250A	2500	4000/2750	15/8.6	1.15/0.90	0.28/0.25	24	110	1200	77
400A/400A.G	4000	6300/4400	24/14	1.30/1.20	0.35/0.30	24	123	1000	122
630A.G	6300	6800	22.5	2.1	0.4	24	137	900	194
1000A.G	10000	11000	36	3.6	0.6	24	180	750	300

Note: G is dry multi-disc electromagnetic clutch
Note: G express the electromagnetic multidisc clutch of dry operation

Installation Schematic
Installation Diagram

Outline and installation dimensions
Shape and Installation Dimensions

Specifications Model	Radial Dimensions									Axial dimension Axial Dimensions						Brush model Brush Model
	D1	D2	D3	D4	Φ	e	h	J	K	L	L1	L2	L3	L4	E
1A/ 1A.G	100	100	85	50	18	50 0.025	19.9 0.14	2Xφ6	4XM6	45	42	5	5.5	8	0.30	wet Adopt DS-005 dry type Adopt DS-006
2A/ 2A.G	110	110	90	55	20	60 0.025	22.3 0.14	2Xφ6	4XM6	48	45	5	5.5	8	0.30
4A/ 4A.G	120	120	100	60	25	80 0.03	27.6 0.14	3Xφ6	6XM6	52	48	6	5.5	8	0.30
6A/6A.G	132	132	105	65	30	80 0.03	32.6 0.17	3Xφ6	6XM8	55	50	7	5.5	8	0.30
10A/ 10A.G	147	145	120	75	40	120 0.035	42.9 0.17	3Xφ8	6XM8	58	53	7	5.5	8	0.35
16A/ 16A.G	162	160	135	85	45	140 0.035	48.3 0.17	3Xφ8	6XM8	62	57	7	5.5	8	0.40
25A/ 25A.G	182	180	155	95	50	160 0.035	53.60 0.20	3Xφ10	6X M10	68	63	8	6	8	0.45
40A/ 40A.G	202	200	170	120	60	180 0.035	64 0.20	3Xφ10	6X M10	76	70	9	6.25	8	0.50
63A/ 63A.G	235	230	200	125	70	200 0.0435	74.3 0.20	3Xφ14	6X M12	86	80	10	6.25	8	0.60
100A/ 100A.G	270	255	235	150	70	200 0.0435	74.3 0.20	3Xφ14	6X M12	100	92	12	8.5	10	0.70
160A/ 160A.G	310	295	260	180H8	75	20±0.026	81.1 0.20	3Xφ16	6X M16	115	107	14	8	10	0.80
250A/ 250A.G	360	340	305	200H8	100	28±0.026	106.4 0.20	3Xφ16	6X M16	132	122	15	8.5	10	0.90
400A/ 400A.G	420	395	350	235H8	120	320 0.05	126.7 0.20	4Xφ20	6X M16	150	138	17	8.5	10	1
630A.G	485	455	400	235 H8	130	32 0.01 0.07	136.7 0.20	4Xφ20	8X M20	172	157	20	10.5	12	1.1
1000A.G	560	530	460	280	145	32±0.03	154.2 0.20	4Xφ25	4X M24	200	183	22	10.5	12	1.3.

Note: 1. D3, J and K listed in the table are user connection dimensions, which are processed by the user. The data in this table are for reference only.

2.250A/250AG,400A/ 400A.G, 630A.G, 1000A.G,G is a double bond hole, the position is 180, h1 is 112.80 0.2,113.40 0.52,143.40 0.52,163.40 0.2

Remark:1. D3、J、K list in the list are sizes using for join of customer and processed by customer himself. The data of this list are for reference only

2. 250A/250AG，400A/ 400A.G、630A.G、1000A.G，G are double-Kay hole. The position in 180°,h1 is 112.8 plus0 0.2,133.4 plus0 0.52,143.4 plus0 0.52,163.4 plus0 0.2

IsraelDLM5 Series Wet Multi-disc Electromagnetic Clutch

IsraelDLMT Series Wet Multi-disc Electromagnetic Clutch

: next page

The company has a product research and development department composed of experts, senior engineers and other professional and technical personnel. It is engaged in research and development and has perfect research and development test equipment. At present, the products reach more than 100 series of nearly 1,000 specifications, and the force distance ranges from 0.1N. m ~ 250000N.m. The company has been rated as a high-tech enterprise by the state for more than ten consecutive years, and a number of R & D projects have been established locally and have received municipal financial support.

Gate control system clutch

Electromagnetic brake for rail transit system

Robot special clutch

Special Clutch for Medical Equipment

Permanent magnet clutch

Jaw electromagnetic clutch

Single-plate electromagnetic clutch

Electromagnetic power-loss clutch

Electromagnetic clutch brake

Slip clutch HC3-25B (rubber plate machine)

Special for DLM2 series rolling mill

ZAA series metallurgy, steel industry special